Your Subtitle text
AFTERBURNER II™ Specifications
- Input Impedance Balanced 20K ohms, Unbalanced 10K ohms
- Input Headroom + 22 dB
- CMRR >60 dB, 20 Hz-20 KHz
- Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
- Output Level (Max) + 22 dB
- Frequency Response 20Hz to 20KHz ±0.2dB
- Signal to Noise Ratio -93 dB Unweighted, -99 dB 'A' weighted
- Distortion .02% THD @ 0dB, 1KHz
- Dynamic Range 115 dB
- Sidechain Insert Impedance 10K ohm
- Filter Type Phase corrected 6dB/octave
- Summed Filter Response ±0.2dB through crossover region
- Dividing Frequency 250 Hz
- Low Enhance 50 Hz, High Enhance 10 KHz
- Power Requirements 100/120 V AC, 220/240 V AC
- Weight 5 lbs/2.2 Kg
- Dimensions 19" W x 1-3/4" H x 6" D, 482 x 44 x 155mm
- Input/Output Connector Type Balanced XLR
- Sidechain Insert Connector Balanced TRS
- Hardwire bypass IN/OUT switch
- Threshold, Ratio and Output Gain controls
- Above/Below Threshold LED’s
- 12 segment LED Output Level display
- Numbered marker panel for labeling compressor assigns
- 7 segment LED Gain Reduction display
- Enhance switch and status LED
- Adaptive Stereo link switch and status LED
- Dual/Single channel mode switch and status LED’s
- Balanced Inputs and Outputs, on both XLR and TRS jack connectors. In Single channel (Mono) mode, use Channel 1 Inputs and Outputs only
- Sidechain Insert TRS connector on each channel AC input connector, with voltage switch and fuse.
Quadcomp®II Specifications
- Input Impedance
- Balanced 20K ohms, Unbalanced 10K ohms
- Input Headroom + 20dB
- CMRR >50dB, 20 Hz—20 KHz
- Output Impedance
- Balanced 300 ohms Unbalanced 150 ohms
- Output Level (Max) + 20dB
- Frequency Response 20Hz-20KHz ±0.5dB
- Signal to Noise Ratio -93 dB Unweighted, -98 dB ‘A’ weighted
- Distortion .015% THD @ 0dB, 1KHz
- Dynamic Range 108 dB
- Attack and Release Times Program dependent
- Metering
- 7 LED display: –1, 2, 3, 6, 12, 18, –24 dB
- Sidechain Insert Impedance 10K ohm
- Power Requirements
- 100/120 V AC or 220/240 V AC
- Weight 5 lbs/2.2 Kg
- Dimensions 19"W x 13/4"H x 6"D, 482 x 44 x 155mm
- Input Connector type Balanced XLR
- Output Connector type Balanced XLR
- Sidechain Insert Connector TRS Jack
- Hardwire bypass IN/OUT switch
- Threshold, Ratio and Output Gain controls
- 7 LED Gain Reduction display
- Marker panel for labeling compressor assigns
- Stereo link status LED’s
- Input and Output balanced XLR connectors
- TRS Sidechain insert connectors
- Channels 1 and 2, 3 and 4 Stereo link switches
- IEC AC mains connector with inbuilt fuse and voltage change
COMPO™ Specifications
- Input Impedance Balanced 20K ohms, Unbalanced 10K ohms
- Input Headroom + 22dB
- CMRR >60dB, 20 Hz-20 KHz
- Output Impedance Balanced 300 ohms, Unbalanced 150 ohms
- Output Level (Max) + 22dB
- Frequency Response 20Hz to 20KHz ±0.4dB
- Signal to Noise ratio -85dB Unweighted, -99dB 'A' weighted
- Distortion .02% THD @ 0dB, 1KHz
- Dynamic Range 107dB
- Low Enhance 50 Hz, High Enhance 10 KHz
- Power Requirements 100/120 V AC, 220/240 V AC
- Weight 5 lbs/2.2 Kg
- Dimensions 19" W x 1-3/4" H x 6" D, 482 x 44 x 155mm
- Input/Output Connector type Balanced XLR & TRS Jack
- Channel A Active/Bypassed IN/OUT switch
- Threshold, Ratio and Output Gain controls
- Numbered marker panel for labeling compressor assigns
- 5 segment LED Gain Reduction display
- Above/Below Threshold status LED’s
- Enhance switch and status LED
- Stereo link switch and status LED
- Channel B controls identical to Channel A
- Balanced XLR Input and Output connectors.
- Balanced TRS jack Input and Output connectors.
- AC input connector, with voltage switch and fuse.
Sixgate™ Specifications
- Input Impedance
- Balanced 20K ohms, Unbalanced 10K ohms
- Input Headroom + 22dB
- CMRR >60dB, 20 Hz-20 KHz
- Output Impedance
- Balanced 300 ohms, Unbalanced 150 ohms
- Output Level (Max) + 20dB
- Frequency Response 20Hz to 20KHz ±0.2dB
- Signal to Noise Ratio
- Gate Closed: -95dB Unweighted, -105dB 'A' weighted
- Gate Open: Depth Minimum: -93.5dB Unweighted -98dB 'A' weighted
- Distortion 0 .01% THD @ 0dB,1KHz
- Dynamic Range 125dB
- Attack Time Program dependent using high-speed opto-couplers
- Release Time User variable
- Input and Output Connector type Balanced TRS Jack
- Sidechain Insert Connector TRS Jack
- Sidechain Insert Impedance 10K ohm
- Power Requirements 100/120 V AC, 220/240 V AC
- Weight 5 lbs/2.2 Kg
19" Wide x 1-3/4" High x 6" Deep; 482 x 44 x 155mm
Front Panel Controls
- Individual Release, Depth and Threshold controls
- Hardwire bypass IN/OUT switch with status LED
- Open/Closed gate status LED
- Marker panel for labeling gate assigns
- Balanced Inputs and Outputs, on Balanced TRS jack connectors
- Sidechain Insert/Key Input TRS jack on each channel
- AC input connector, with voltage switch and fuse
